Quartz concentration trends in metal and nonmetal mining

Winthrop F. Watts, Tran B. Huynh, Gurumurthy Ramachandran

Research output: Contribution to journalArticle

Abstract

From 1974 through 2010, the Mine Safety and Health Administration (MSHA) collected nearly 147,000 respirable dust samples with a mass of at least 0.1 mg and a minimum of 1% quartz. These samples represent about 50% of all respirable dust compliance samples collected by MSHA. Analysis of these data shows that pockets of high concentrations and overexposure continue to exist. At underground mines, from 2005 to 2010, occupations with >20% of the samples exceeding the permissible exposure limit (PEL) and geometric mean quartz concentrations exceeding the ACGIH threshold limit value of 25 μg/m3 included mucking, crusher operator, general laborer/utility, and front-end loader operator. During the same period, stone and rock saw operators and bagger and packers working at surface mines and mills also had >20% of the samples exceeding the PEL and geometric mean quartz concentrations >25 μg/m3. Regardless of mine type or location, slow but steady improvement in exposure levels is seen in jobs involving crushing operations, which are widespread in the mining industry. Crusher operators are more likely to work in an enclosed area where it is easier to apply dust controls and air conditioning. A downward trend is also observed for vehicle equipment operators who drive loadhaul- dumps, front-end loaders, trucks, and similar equipment. Crusher operators and vehicle equipment operators represent occupational categories that are widely sampled by MSHA inspectors. A small but statistically significant reduction in the overall mean respirable quartz dust and quartz concentrations from 1993 to 2010 was observed in most commodity groups. Variability from year to year and between commodities is high. Reduction in respirable quartz dust concentration does not necessarily correspond to a reduction in quartz concentration within the same commodity group. These trends are consistent with those reported in previous studies.

Original languageEnglish (US)
Pages (from-to)720-732
Number of pages13
JournalJournal of Occupational and Environmental Hygiene
Volume9
Issue number12
DOIs
StatePublished - 2012
Externally publishedYes

Fingerprint

Quartz
Metals
Dust
Safety
Equipment and Supplies
Health
Threshold Limit Values
Air Conditioning
Motor Vehicles
Occupations
Compliance
Industry

Keywords

  • Metal and nonmetalmining
  • Quartz dust
  • Respirable dust

ASJC Scopus subject areas

  • Public Health, Environmental and Occupational Health

Cite this

Quartz concentration trends in metal and nonmetal mining. / Watts, Winthrop F.; Huynh, Tran B.; Ramachandran, Gurumurthy.

In: Journal of Occupational and Environmental Hygiene, Vol. 9, No. 12, 2012, p. 720-732.

Research output: Contribution to journalArticle

@article{10f1d23873fa4b4b9a518a121c1b2317,
title = "Quartz concentration trends in metal and nonmetal mining",
abstract = "From 1974 through 2010, the Mine Safety and Health Administration (MSHA) collected nearly 147,000 respirable dust samples with a mass of at least 0.1 mg and a minimum of 1{\%} quartz. These samples represent about 50{\%} of all respirable dust compliance samples collected by MSHA. Analysis of these data shows that pockets of high concentrations and overexposure continue to exist. At underground mines, from 2005 to 2010, occupations with >20{\%} of the samples exceeding the permissible exposure limit (PEL) and geometric mean quartz concentrations exceeding the ACGIH threshold limit value of 25 μg/m3 included mucking, crusher operator, general laborer/utility, and front-end loader operator. During the same period, stone and rock saw operators and bagger and packers working at surface mines and mills also had >20{\%} of the samples exceeding the PEL and geometric mean quartz concentrations >25 μg/m3. Regardless of mine type or location, slow but steady improvement in exposure levels is seen in jobs involving crushing operations, which are widespread in the mining industry. Crusher operators are more likely to work in an enclosed area where it is easier to apply dust controls and air conditioning. A downward trend is also observed for vehicle equipment operators who drive loadhaul- dumps, front-end loaders, trucks, and similar equipment. Crusher operators and vehicle equipment operators represent occupational categories that are widely sampled by MSHA inspectors. A small but statistically significant reduction in the overall mean respirable quartz dust and quartz concentrations from 1993 to 2010 was observed in most commodity groups. Variability from year to year and between commodities is high. Reduction in respirable quartz dust concentration does not necessarily correspond to a reduction in quartz concentration within the same commodity group. These trends are consistent with those reported in previous studies.",
keywords = "Metal and nonmetalmining, Quartz dust, Respirable dust",
author = "Watts, {Winthrop F.} and Huynh, {Tran B.} and Gurumurthy Ramachandran",
year = "2012",
doi = "10.1080/15459624.2012.733566",
language = "English (US)",
volume = "9",
pages = "720--732",
journal = "Journal of Occupational and Environmental Hygiene",
issn = "1545-9624",
publisher = "Taylor and Francis Ltd.",
number = "12",

}

TY - JOUR

T1 - Quartz concentration trends in metal and nonmetal mining

AU - Watts, Winthrop F.

AU - Huynh, Tran B.

AU - Ramachandran, Gurumurthy

PY - 2012

Y1 - 2012

N2 - From 1974 through 2010, the Mine Safety and Health Administration (MSHA) collected nearly 147,000 respirable dust samples with a mass of at least 0.1 mg and a minimum of 1% quartz. These samples represent about 50% of all respirable dust compliance samples collected by MSHA. Analysis of these data shows that pockets of high concentrations and overexposure continue to exist. At underground mines, from 2005 to 2010, occupations with >20% of the samples exceeding the permissible exposure limit (PEL) and geometric mean quartz concentrations exceeding the ACGIH threshold limit value of 25 μg/m3 included mucking, crusher operator, general laborer/utility, and front-end loader operator. During the same period, stone and rock saw operators and bagger and packers working at surface mines and mills also had >20% of the samples exceeding the PEL and geometric mean quartz concentrations >25 μg/m3. Regardless of mine type or location, slow but steady improvement in exposure levels is seen in jobs involving crushing operations, which are widespread in the mining industry. Crusher operators are more likely to work in an enclosed area where it is easier to apply dust controls and air conditioning. A downward trend is also observed for vehicle equipment operators who drive loadhaul- dumps, front-end loaders, trucks, and similar equipment. Crusher operators and vehicle equipment operators represent occupational categories that are widely sampled by MSHA inspectors. A small but statistically significant reduction in the overall mean respirable quartz dust and quartz concentrations from 1993 to 2010 was observed in most commodity groups. Variability from year to year and between commodities is high. Reduction in respirable quartz dust concentration does not necessarily correspond to a reduction in quartz concentration within the same commodity group. These trends are consistent with those reported in previous studies.

AB - From 1974 through 2010, the Mine Safety and Health Administration (MSHA) collected nearly 147,000 respirable dust samples with a mass of at least 0.1 mg and a minimum of 1% quartz. These samples represent about 50% of all respirable dust compliance samples collected by MSHA. Analysis of these data shows that pockets of high concentrations and overexposure continue to exist. At underground mines, from 2005 to 2010, occupations with >20% of the samples exceeding the permissible exposure limit (PEL) and geometric mean quartz concentrations exceeding the ACGIH threshold limit value of 25 μg/m3 included mucking, crusher operator, general laborer/utility, and front-end loader operator. During the same period, stone and rock saw operators and bagger and packers working at surface mines and mills also had >20% of the samples exceeding the PEL and geometric mean quartz concentrations >25 μg/m3. Regardless of mine type or location, slow but steady improvement in exposure levels is seen in jobs involving crushing operations, which are widespread in the mining industry. Crusher operators are more likely to work in an enclosed area where it is easier to apply dust controls and air conditioning. A downward trend is also observed for vehicle equipment operators who drive loadhaul- dumps, front-end loaders, trucks, and similar equipment. Crusher operators and vehicle equipment operators represent occupational categories that are widely sampled by MSHA inspectors. A small but statistically significant reduction in the overall mean respirable quartz dust and quartz concentrations from 1993 to 2010 was observed in most commodity groups. Variability from year to year and between commodities is high. Reduction in respirable quartz dust concentration does not necessarily correspond to a reduction in quartz concentration within the same commodity group. These trends are consistent with those reported in previous studies.

KW - Metal and nonmetalmining

KW - Quartz dust

KW - Respirable dust

UR - http://www.scopus.com/inward/record.url?scp=84874146049&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84874146049&partnerID=8YFLogxK

U2 - 10.1080/15459624.2012.733566

DO - 10.1080/15459624.2012.733566

M3 - Article

C2 - 23092305

AN - SCOPUS:84874146049

VL - 9

SP - 720

EP - 732

JO - Journal of Occupational and Environmental Hygiene

JF - Journal of Occupational and Environmental Hygiene

SN - 1545-9624

IS - 12

ER -